Stream Joystick:
, : Selects options from streaming/recording prompts
● (button press): Returns to main status screen
Menu Joystick:
▲,▼: Select menu items, change status screen on main display, select characters
: Back, move to higher menu level
,● (button press): Confirm selection, open selected menu
▲
▲
▲
▲
NETWORK CONNECTION
DECODER CONFIGURATION
Connect A/C power to the Power Input (J). Attach the included Wireless antennas via the
threaded RP-SMA connectors (G).
Connect SDI video to your monitor (P). Connect analog audio (I).
Connect Slice to your network via the 10/100 Ethernet port (L).
In Infrastructure mode, Slice connects to an existing network via a wireless access point or Ethernet
connection. Infrastructure mode allows Slice to communicate with all devices on the network and is required
for streaming to the Internet.
Wireless range can be greatly improved by using a wireless access point.
POWER & CONNECT
1
2
3
1
3
2
INFRASTRUCTURE MODE: Add Slice to an existing network.
1. Enter the main menu by pressing
▲
or ●.
Select Network Setup with ▼ and enter the
menu with
▲
.
2. Select Configure.
6. If prompted, enter your network password. Choose
characters with ▲ and ▼, choose the position
with
▲
and
▲
, and confirm with ●. To cancel, press ●.
4. From the WiFi Configuration menu, choose Scan.
3. Select Mode, and then choose Infrastructure.
The Wireless mode will be set.
8. Once configured, you can view the network status
by selecting Status from the Network Setup menu.
7. Choose Yes to apply the new network settings.
5. Select your preferred network, (the
*
icon
indicates a secured network), and the number
on the far right is the signal strength.
NEED MORE HELP? Support forum: http://support.teradek.com → Contains tips, information and all the latest firmware &
software updates. TERADEK SUPPORT STAFF: support@teradek.com or call 888−941−2111 ext2 (Mon−Fri 9am to 6pm PST)
A: Video Status
B: Codec Status
C: Broadcast/Record
D: Fault/Error
E: Menu Joystick
F: Stream Joystick
G: WiFi Antennas
H: MIC Audio Input
I: RCA Audio Output
J: Power Input
K: A/C Input
L: Ethernet Port
M: Reset Button
N: USB Port
O: Micro SD Card Slot
P: SDI Output
A
B
C
D
E
F
Decoder
J
L
O PNM
K
G
H
I
Decoder Settings
Automatic − For use with Teradek Encoders on a local network
1. Select a Stream to Decode from the select box in the ‘Pairing’ section.
2. Select a video output resolution, if desired.
3. Click Apply.
RTSP
1. Select a protocol (UDP/TCP), and configure the ‘Host’ IP address, ‘Port’ and stream ‘Name’ settings to match
ghyour RTSP source. For Teradek encoders, the default port is 554, and the default stream name is stream1.
2. Select a video ‘Output Resolution’.
3. Select ‘Audio’ Enabled or disabled and the desired ‘Stereo Mode’.
4. Click Apply.
MPEG Transport Stream
1. Select a ‘Protocol’ − TCP, UDP, Multicast, or TCP Pull − to match your video source. Use TCP, UDP, or multicast
when receiving MPEG−TS directly from Teradek encoders, or TCP Pull when connecting to a Transport Stream
server like Sputnik.
2. For Multicast and TCP Pull only − enter a ‘Host’ IP address to match the source’s multicast or Transport Stream
server address.
3. Enter a valid ‘Port’ to match the MPEG−TS source.
4. Select a video ‘Output Resolution’.
5. Select ‘Audio’ Enabled or disabled and the desired ‘Stereo Mode’.
6. Click Apply.
Connecting Slice to an existing wireless network:
(2 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais